Seal-It! (Deep Penetrating Sealer) is a problem solver. It treats concrete and masonry three ways; it permanently seals out water, densifies and hardens it all at once. It contains a catalyst that seeks out and reacts with moisture, free alkali (lime), calcium hydroxides and other particles fusing them together creating an impenetrable silica. The entire matrix is converted into a solid mass creating a permanent barrier. Increases the bonding power floor coating products by up to 300%. Withstands up to 60 PSI hydro-static pressure! A true penetrating sealer not intended to be used over sealed surfaces or paint. Not a coating that leaves a finish! See concrete floor paints and coating products for finishes. One gallon treats 200 square feet. Three applications typically required. We strongly recommend making the VaproGuage Moisture Test part of your order. Call us or refer to product Data Sheet for further details.
Removes most liquid applied coatings quickly and easily.
Does not contain any flammable materials.
INTENDED USE: Use to remove urethane and epoxy boat paints, primer and clear finishes. Acceptable for use on epoxy marine paints.
SURFACES: Metal, concrete, glass, tile, and wood. Note: Not for use on fiberglass or plastic.
Triple Strength Paint Stripper is a fast acting water-based paint stripper that is very effective. It contains no caustic, acid, or flammable solvent. This product readily removes paint, varnish, lacquer, baked enamel and shellac quickly and safely from most surfaces. Out performs typical stripper / cleaners. One gallon removes approximately 200 square feet of paint.
SURFACES: Fiberglass, aluminum, wood, synthetic materials and all metals.
USES: Fill, repair and seal cracks, seams, voids and expansion joints in hulls, decks, bilges, floor, wall, roof and similar structures typically in preparation for a paint or coating product.
PRIMER: None typically required.
Application: Apply to clean dry surfaces with a calking gun.
TS-670 EMCU Moisture Cure Urethane Sealer is used for filling, repairing and sealing cracks, seams, voids and joints on floors, boats, and swimming pools as well as in architectural applications. A superior grade elastomeric polyurethane sealant that utilizes moisture present in air to achieve the cure eliminating the need for mixing resin with catalyst. It is easy to use, versatile and highly durable. The high solid content resin (96% solid) will not sag when applied to vertical and overhead surfaces and has a low shrink ratio. It will bond to most any substrate including concrete, fiberglass, aluminum, tile, masonry, plaster, steel, vinyl and wood. It is acceptable in constant water immersion duty when over-coated with protective waterproof paint. The tube fits easily in any standard thrust type calking gun. It is low odor and low VOC. The product is supplied in individual tubes for use with typical caulking guns with a suitable thrust ratio. It is available in single tubes or cases of 24 pieces per package (300ml per cartridge is 10.1 fl oz). Color is Limestone (light gray). Complies to ASTM C920 Type S, Federal specification TT-S-00230C Type II, Corp of Engineers CRD-C-541, Type II, Class A.
APPLICATION: Mix 1 part concentrate with 3 parts water. Apply to pre-wet surface, allow to stand 20-30 minutes, flush with water. Use undiluted for heavy-duty requirements.
Etching Cleaner Concentrate is a cleaner-etcher solution used as a preparation treatment on concrete, tile and masonry. Widely used on pool and deck surfaces prior to the application of paint and sealer products. Removes unwanted contaminants and neutralizes lime and lime by-products on the surface which may seriously impair the coatings’ ability to form a good bond. It is easier to use and more effective than muriatic acid. Removes lime, rust stains, grease, oil, calcium and contaminates from bare as well as painted surfaces. Corrects the pH on concrete and other surfaces promoting adhesion. Concentrate saves money on shipping costs. Mixed pint cleans 50-75 sq. ft., mixed quart cleans 200 square feet, mixed gallon cleans 800 square feet.
Loading... Please wait.
Aquapoxy Paint - 18701 58th Ave. N.E., Bldg #43, Arlington, WA 98223, US