Supporting Products

TS-670 EMCU Moisture Cure Urethane Sealer is used for filling, repairing and sealing cracks, seams, voids and joints on floors, boats, and swimming pools as well as in architectural applications. A superior grade elastomeric polyurethane sealant that utilizes moisture present in air to achieve the cure eliminating the need for mixing resin with catalyst. It is easy to use, versatile and highly durable. The high solid content resin (96% solid) will not sag when applied to vertical and overhead surfaces and has a low shrink ratio. It will bond to most any substrate including concrete, fiberglass, aluminum, tile, masonry, plaster, steel, vinyl and wood. It is acceptable in constant water immersion duty when over-coated with protective waterproof paint. The tube fits easily in any standard thrust type calking gun. It is low odor and low VOC. The product is supplied in individual tubes for use with typical caulking guns with a suitable thrust ratio. It is available in single tubes or cases of 24 pieces per package (300ml per cartridge is 10.1 fl oz). Color is Limestone (light gray). Complies to ASTM C920 Type S, Federal specification TT-S-00230C Type II, Corp of Engineers CRD-C-541, Type II, Class A.

Power-Patch (TS-671) ) is an expanding, fast setting, pourable hydraulic type cement used to patch repair and fill voids, breaks, cracks and joints in concrete, masonry, tile, terrazzo cement. It is acceptable for use on floors, swimming pools, stairs, ramps, landings, walls or most any cementious surface. It saves repair dollars because it ensures permanent results making it perfect for use in commercial, industrial and residential applications. When mixed with water to a pourable consistency, it flows and seeps into place filling voids and cracks thoroughly. It takes and initial set within 15 minutes. It dries quickly, harder than concrete in less than one hour. Once fully cured it has more than twice the strength of fully cured conventional concrete. Within one hour it develops a compression strength of 4500 LBS. per square inch. Its adhesion is due to expansion, and when fully set it grips metal to concrete permanently. Color is light gray. Available in 5LB, 10LB and 50LB packages.

Seal-It! (Deep Penetrating Sealer) is a problem solver. It treats concrete and masonry three ways; it permanently seals out water, densifies and hardens it all at once. It contains a catalyst that seeks out and reacts with moisture, free alkali (lime), calcium hydroxides and other particles fusing them together creating an impenetrable silica. The entire matrix is converted into a solid mass creating a permanent barrier. Increases the bonding power floor coating products by up to 300%. Withstands up to 60 PSI hydro-static pressure! A true penetrating sealer not intended to be used over sealed surfaces or paint. Not a coating that leaves a finish! See concrete floor paints and coating products for finishes. One gallon treats 200 square feet. Three applications typically required. We strongly recommend making the VaproGuage Moisture Test part of your order. Call us or refer to product Data Sheet for further details.

Triple Strength Paint Stripper is a fast acting water-based paint stripper that is very effective. It contains no caustic, acid, or flammable solvent. This product readily removes paint, varnish, lacquer, baked enamel and shellac quickly and safely from most surfaces. Out performs typical stripper / cleaners. One gallon removes approximately 200 square feet of paint.

Etching Cleaner Concentrate is a cleaner-etcher solution used as a preparation treatment on concrete, tile and masonry. Widely used on pool and deck surfaces prior to the application of paint and sealer products. Removes unwanted contaminants and neutralizes lime and lime by-products on the surface which may seriously impair the coatings’ ability to form a good bond. It is easier to use and more effective than muriatic acid. Removes lime, rust stains, grease, oil, calcium and contaminates from bare as well as painted surfaces. Corrects the pH on concrete and other surfaces promoting adhesion. Concentrate saves money on shipping costs. Mixed pint cleans 50-75 sq. ft., mixed quart cleans 200 square feet, mixed gallon cleans 800 square feet.

Super-Fleck Chips are machine ground acrylic chips used as part of a decorative floor coating system. An optional element that improves the appearance and texture of the surface while adding a measure of safety by improving slip resistance. The effect is a terrazzo-like appearance, which can be customized to meet the individual needs of the user. Disperse chips in light, medium, heavy or full coverage. Chips are UV resistant, colorfast, nontoxic and economical to use. Easy to use; just broadcast them across the still wet surface of the base coat. Clear coat is used to seal them in protecting both the chips and the base coat color. The result is a seamless floor that is both decorative and slip resistant. Chips are available in a wide variety of colors and sizes. Custom colors and color matching services are available by special order. Available in 1 LB, 3 LB, 10 LB and 55 LB quantities. Most surfaces receive medium dispersion, with approximately 1 LB covering about 100-150 square feet. For full dispersion figure approximately 7-10 LBS per 100 square feet. Chip color selection is made part of the check-out process while ordering.

A fine non-skid paint additive that is completely transparent, durable and will not hang up on mops. Excellent when used with clear coatings.

A fine aggregate material that can be added to any floor paint to provide a skid-resistant surface. The 16 oz container mixes with one gallon of paint.

Pro-Tex is a micronized wax additive for liquid coatings that creates a textured slip resistant finish to any paint or clear coating product. Use it to improve slip resistance or simply to add decorative texture to any finish. Acceptable for use with both oil and water based products. It is acceptable for brush and roller-coat applications and it is sprayable. Color is white. DIRECTIONS: pour contents of package into liquid coating product, mix thoroughly, apply evenly. No induction time is required. Recommend using one 8 ounce package per gallon.

Shell-Tex is a finely ground walnut shell additive for liquid coatings that creates a textured slip resistant finish to any paint or clear coating product. Use it to improve slip resistance or simply to add decorative texture to any finish. Acceptable for use with both oil and water based products. It is acceptable for brush and roller-coat applications and it is sprayable. DIRECTIONS: Pour contents of package into liquid coating product, mix thoroughly, apply evenly. No induction time is required. Color is walnut shell. Recommend using 16 ounces per gallon.

Aluma-Tex is a uniformly sized aluminum-oxide additive for liquid coatings that creates a textured slip resistant finish to any paint or clear coating product. Use it to improve slip resistance or simply to add decorative texture to any finish. Acceptable for use with both oil and water based products. It is acceptable for brush and roller-coat applications and it is sprayable. color is dark brown. DIRECTIONS: pour contents of package into liquid coating product, mix thoroughly, apply evenly. No induction time is required.ÿRecommend using 16 ounces per gallon.

A heavy-duty, high quality roller frame made to last for years.

This heavy-Duty adjustable frame can be used with 18” – 9” roller covers.

A standard 9" cage type roller frame with heavy-duty plastic handle. It is threaded for use on any extension pole.

9" Shurline Pro QP foam roller cover with heavy-duty five-wire handle

4" Shurline QP foam roller cover with heavy-duty wire handle

Professional quality texture cover. Should be your first choice for applying aggregate added paint and coatings including Floor-Grip and Floor Grip II. Use it with Tread-Tex aggregate additive for paint. Distributes aggregates evenly across the surface.

Non-Shedding fabric provides exceptional capacity with all flat or satin paints, stains, and floor coatings.

Non-Shedding fabric provides exceptional capacity with all flat or satin paints, stains, and floor coatings.

Features a heavy duty non-shedding moisture resistant and solvent resistant core.

Features a heavy duty, non-shedding, moisture resistant and solvent resistant core.

Features a heavy duty moisture resistant and solvent resistant core.

Best results with all urethane and epoxy pigmented and clear floor coatings, paints and enamels.

Use to achieve a high film build or on rough or textured surfaces.

Designed specifically to disperse aggregates evenly for a uniform dispersal on any surface.

Use to achieve a high film build or on rough or textured surfaces.

Features mohair blend shed-resistant white mohair fabric.

4" Shurline QP foam roller cover 2 pack

A heavy duty, deep well, polypropylene tray designed for use with 14” rollers.

Big roll-off area for 18” frames. One-gallon working capacity saves time. Black polypropylene resists solvents and paint buildup. 16 in. L x 21 in. W x 4 in. D.

A heavy duty, deep well, polypropylene tray, it holds a large amount of paint. It features left and right hand pour spouts and a special herringbone roll out surfaces.

Deluxe Metal Painting Tray features a deep well that allows for maximum paint capacity. Extra width for easy roller refills.

Disposable Plastic Tray Liners designed to be used with all 9” paint trays. Tray liners make cleaning a breeze, just discard when done.

Shurline mini-roller tray for 4" rollers.

This test kit is used to measure the amount of moisture emitted from the surface of a concrete structure. Utilizes anhydrous calcium chloride, included with the kit, to determine the accurate level of vapor transmission in a concrete structure. The kit is easy to use and includes complete easy to read instructions.