|
INSTRUCTIONS FOR APPLYING AQUAPOXY
(TS-905) EPOXY FLOOR SYSTEM Back to www.aquapoxy.com This information has been prepared for use with Aquapoxy on properly prepared surfaces. Allow new concrete to cure a min of 28 days before application. Recommend eliminating the possibility of hydrostatic pressure by using a properly adjusted moisture meter, VaporGuage calcium chloride moisture test, or the equivalent. Where hydrostatic pressure is present, or suspected, recommend using TS-104 Seal-it!. For best results apply two (or more) coats by roller coat or squeegee. Recommended roller-coat Wet Film Thickness (WFT) is 4-5 mils, squeegee WFT is 8-12 mils per coat basis. Squeegee applications will likely require thinning with water. We recommend using 3/8” non-shedding roller cover on smooth surfaces, use higher nap covers on rough surfaces. May be applied as low as 55F however best results are obtained between 65F and 80F. Do not apply above 85F or in hot direct sunlight. All floor applications will require removal of all grease, oil, glue and contaminates and the use of either TS-695 Etching Cleaner or TS-104 Seal-It!. Recommend removing existing coatings or sealers for best results. Existing coatings in sound condition must be scuffed. Failing coatings should be stripped bare. Aquapoxy is not recommended for use on wood or similarly flexible substrates. All recommendations, written and verbal directions, label instructions and standard industry practices must be strictly followed or guaranty is voided.
1. PREP-WORK: All repairs should be
completed and allowed to cure prior to sanding, blasting, grinding or
application. Sanding, grinding or blasting is beneficial but often not
required where circumstances and conditions permit, you must be
the judge, consider carefully before proceeding. Be sure all repair
materials are paintable. Recommend using either TS-695 Etching Cleaner
or TS-104 Seal-It! according to label directions. Recommend choosing
TS-104 Seal-It! over TS-695 Etching Cleaner where there is evidence or
suspicion of hydrostatic pressure. Aquapoxy is self priming so the use
of Aquapoxy Primer (TS-910) is optional. Aquapoxy Primer is typically
used in applications where higher film build is desired. Apply Mono
Epoxy Primer as outlined in step 2. 2. APPLY COLOR COAT & CHIPS: Stir Aquapoxy (TS-905) A&B components together using a high speed mixer for 30 -60 seconds. Allow to stand 30 minutes, stir again for 1 minute. POT LIFE: 3-4 hour temp dependant, stir regularly and add water to extend pot life. Recommend Hand brushing the edges then roll coat the remaining area. Apply evenly avoiding heavy build up and overlaps. Always keep a wet edge when rolling. If using chips broadcast them evenly onto the still wet surface within 5 minutes for best adhesion. Repeat process until entire area has been treated equally. Aquapoxy Clear coat is required to seal in and protect the chips. Allow to stand a minimum of 12 hours before applying next coat. Aquapoxy should be recoated within 12-48 hours.
3. APPLY TOP COAT: Stir Aquapoxy Clear (TS-905) A&B components together using a high speed mixer for 30 -60 seconds. Allow to stand 30 minutes then stir again for 1 minute. Apply evenly with ¼” or 3/8” non-shedding roller cover avoiding overlaps and heavy build up. Warning: Too heavy application (clear) may result in unwanted amber resin color! Allow to stand a minimum of 12 hours before allowing light foot traffic and 48 hours minimum before allowing light motorized traffic, as circumstances allow. Do not allow moisture for 48 hours min. Temperatures above 80F or low humidity conditions may require thinning with water. Actual times may vary.
NOTE: Never apply Aquapoxy where there is hydrostatic pressure exceeding 5 LBS PSI. Use TS-104 Seal-It! to stop hydrostatic pressure. Dry and cure time vary with the weather, temperature, ventilation, thickness of application and color. Allow extra dry and cure time for dark colors. We hope this information helps you achieve the results you expect and years of problem free service. We are available to answer questions at 360-651-9050 M-F 9 AM to 5 PM PST.
. |